Pickering Driver Error Codes
Pickering Driver Error Codes - Pilpxi.h
| 0
|
NO_ERR
|
No Error
|
| 1
|
ER_NO_CARD
|
No Pickering card has the specified number
|
| 2
|
ER_NO_INFO
|
Card information unobtainable - hardware problem
|
| 3
|
ER_CARD_DISABLED
|
Card disabled - hardware problem |
| 4
|
ER_BAD_SUB
|
Sub-unit value out-of-range for target card
|
| 5
|
ER_BAD_BIT
|
Bit-number out-of-range for target sub-unit
|
| 6
|
ER_NO_CAL_DATA
|
Target sub-unit has no calibration data to read/write
|
| 7
|
ER_BAD_ARRAY
|
Array type, shape or size is incorrect |
| 8
|
ER_MUX_ILLEGAL
|
Non-zero write data is illegal for MUX sub-unit
|
| 9
|
ER_EXCESS_CLOSURE
|
Sub-unit closure limit exceeded |
| 10
|
ER_ILLEGAL_MASK
|
One or more of the specified channels cannot be masked
|
| 11
|
ER_OUTPUT_MASKED
|
Cannot activate an output that is masked
|
| 12
|
ER_BAD_LOCATION
|
Cannot open a Pickering card at the specified location
|
| 13
|
ER_READ_FAIL
|
Failed read from hardware
|
| 14
|
ER_WRITE_FAIL
|
Failed write to hardware
|
| 15
|
ER_DRIVER_OP
|
Hardware driver failure
|
| 16
|
ER_DRIVER_VERSION
|
Incompatible hardware driver version
|
| 17
|
ER_SUB_TYPE
|
Function call incompatible with sub-unit type or capabilities
|
| 18
|
ER_BAD_ROW
|
Matrix row value out-of-range
|
| 19
|
ER_BAD_COLUMN
|
Matrix column value out-of-range
|
| 20
|
ER_BAD_ATTEN
|
Attenuation value out-of-range
|
| 21
|
ER_BAD_VOLTAGE
|
Voltage value out-of-range
|
| 22
|
ER_BAD_CAL_INDEX
|
Calibration reference out-of-range |
| 23
|
ER_BAD_SEGMENT
|
Segment number out of range
|
| 24
|
ER_BAD_FUNC_CODE
|
Function code value out of range
|
| 25
|
ER_BAD_SUBSWITCH
|
Subswitch value out of range
|
| 26
|
ER_BAD_ACTION
|
Action code out of range
|
| 27
|
ER_STATE_CORRUPT
|
Cannot execute due to corrupt sub-unit state
|
| 28
|
ER_BAD_ATTR_CODE
|
Unrecognised attribute code
|
| 29
|
ER_EEPROM_WRITE_TMO
|
Timeout writing to EEPROM
|
| 30
|
ER_ILLEGAL_OP
|
Operation is illegal in the sub-unit's current state
|
| 31
|
ER_BAD_POT
|
Unrecognised pot number requested
|
| 32
|
ER_MATRIXR_ILLEGAL
|
Invalid write pattern for MATRIXR/MATRIXS sub-unit |
| 33
|
ER_MISSING_CHANNEL
|
Attempted operation on non-existent channel
|
| 34
|
ER_CARD_INACCESSIBLE
|
Card cannot be accessed (failed/removed/unpowered)
|
| 35
|
ER_BAD_FP_FORMAT
|
Unsupported internal floating-point format (internal error)
|
| 36
|
ER_UNCALIBRATED
|
Sub-unit is not calibrated
|
| 37
|
ER_BAD_RESISTANCE
|
Unobtainable resistance value
|
| 38
|
ER_BAD_STORE
|
Invalid calibration store number
|
| 39
|
ER_BAD_MODE
|
Invalid mode value
|
| 40
|
ER_SETTINGS_CONFLICT
|
Conflicting device settings
|
| 41
|
ER_CARD_TYPE
|
Function call incompatible with card type or capabilities
|
| 42
|
ER_BAD_POLE
|
Switch pole value out of range
|
| 43
|
ER_MISSING_CAPABILITY
|
Attempted to activate a non-existent capability
|
| 44
|
ER_MISSING_HARDWARE
|
Action requires hardware that is not present
|
| 45
|
ER_HARDWARE_FAULT
|
Faulty hardware
|
| 46
|
ER_EXECUTION_FAIL
|
Failed to execute (e.g. blocked by a hardware condition)
|
| 47
|
ER_BAD_CURRENT
|
Current value out of range
|
| 48
|
ER_BAD_RANGE
|
Invalid range value
|
| 49
|
ER_ATTR_UNSUPPORTED
|
Attribute not supported
|
| 50
|
ER_BAD_REGISTER
|
Register number out of range
|
| 51
|
ER_MATRIXP_ILLEGAL
|
Invalid channel closure or write pattern for MATRIXP sub-unit
|
| 52
|
ER_BUFFER_UNDERSIZE
|
Data buffer too small
|
| 53
|
ER_ACCESS_MODE
|
Inconsistent shared access mode
|
| 54
|
ER_POOR_RESISTANCE
|
Resistance outside limits
|
| 55
|
ER_BAD_ATTR_VALUE
|
Bad attribute value
|
| 56
|
ER_INVALID_POINTER
|
Invalid pointer
|
| 57
|
ER_ATTR_READ_ONLY
|
Attribute is read only
|
| 58
|
ER_ATTR_DISABLED
|
Attribute is disabled
|
| 59
|
ER_PSU_MAIN_OUTPUT_DISABLED
|
Main output is disabled, cannot enable the channel
|
| 60
|
ER_OUT_OF_MEMORY_HEAP
|
Unable to allocate memory on Heap
|
| 61
|
ER_INVALID_PROCESSID
|
Invalid ProcessID
|
| 62
|
ER_SHARED_MEMORY
|
Shared memory error
|
| 63
|
ER_CARD_OPENED_OTHER_PROCESS
|
Card is opened by a process in exclusive mode
|
| 64
|
ER_DIO_PORT_DISABLED
|
DIO card PORT is disabled due to Over-Current Scenario
|
| 65 | ER_DIO_INVALID_FILE | DIO pattern File is invalid |
| 66 | ER_DIO_DYNAMIC_ACTIVE | DIO dynamic operation active, action not permissible |
| 67 | ER_DIO_FILE_ENTRY_ERR | DIO file entry error, check file entries |
| 69 | ER_HW_INT_NOT_SUPPORTED | Hardware Interlock feature not supported for the card |
| 70 | ER_HW_INT_ERROR | Hardware Interlock is not detected on the card, cannot use the function |
| 71 | ER_SMS_CH_ENABLE_ERR | Channel is disabled, so Set-Measure-Set cannot be used |
| 72 | ER_MEAS_CURRENT | Measured current out of range |
| 73 | ER_BAD_TEMPERATURE | Temperature value out of range |
| 74 | ER_CMP_ENGINE_ON | Capture engine running - operation unobtainable |
| 75 | ER_WRITEPATTERN_ILLEGAL | Invalid write pattern |
| 76 | ER_DDS_ON | DDS engine running - operation unobtainable |
| 77 | ER_WAVEFORM_UNSUPPORTED | Waveform unsupported |
| 78 | ER_BAD_WAVEFORM | Operation unavailable for selected waveform |
| 79 | ER_FILE_UNAVAILABLE | File unavailable or doesn't exist |
| 80 | ER_BAD_FILE | File content invalid |
| 81 | ER_BAD_AMPLITUDE | Amplitude value out of range |
| 82 | ER_BAD_DC_OFFSET | DC offset value out of range |
| 83 | ER_BAD_FREQUENCY | Frequency value out of range |
| 84 | ER_BAD_PHASE | Phase value out of range |
| 85 | ER_BAD_DUTY_CYCLE | Duty cycle value out of range |
| 86 | ER_BAD_PULSE_WIDTH | Pulse width value out of range |
| 87 | ER_INVALID_COMP_FLAG | Invalid flag for setting compatibility logic |
Card status bits for PIL_Status(), PIL_SubStatus(), PIPLX SubStatus(), and PIPLX SubStatus() results
Note: Two status codes may be combined together
0x10000000 + 0x02000000 = 0x12000000 (Disabled+HW_Fault) [eg Data loop 2 faulty]
| 0x80000000UL
|
STAT_NO_CARD
|
No card with specified number
|
| 0x40000000UL
|
STAT_WRONG_DRIVER
|
Card requires later driver version
|
| 0x20000000U
|
STAT_EEPROM_ERR
|
Error interpreting card EEPROM data
|
| 0x10000000UL
|
STAT_DISABLED
|
Card is disabled
|
| 0x08000000UL
|
STAT_NO_SUB
|
Card has no sub-unit with specified number
|
| 0x04000000UL
|
STAT_BUSY
|
Busy (card or sub-unit)
|
| 0x02000000UL
|
STAT_HW_FAULT
|
Hardware fault (eg. defective serial loop)
|
| 0x01000000UL
|
STAT_PARITY_ERROR
|
9050 Parity Error
|
| 0x00800000UL
|
STAT_PSU_INHIBITED
|
PSU sub-unit - supply is disabled (by software)
|
| 0x00400000UL
|
STAT_PSU_SHUTDOWN
|
PSU sub-unit - supply is shutdown (due to overload)
|
| 0x00200000UL
|
STAT_PSU_CURRENT_LIMIT
|
PSU sub-unit - supply is operating in current-limited mode
|
| 0x00100000UL
|
STAT_CORRUPTED
|
Sub-unit logical state is corrupted
|
| 0x00080000UL
|
STAT_CARD_INACCESSIBLE
|
Card cannot be accessed (failed/removed/unpowered)
|
| 0x00040000UL
|
STAT_UNCALIBRATED
|
Calibration data is faulty (card or sub-unit)
|
| 0x00020000UL
|
STAT_CALIBRATION_DUE
|
Calibration is due (card or sub-unit)
|
| 0x00010000UL
|
STAT_BIRST_ENABLED
|
BIRST is active (card or sub-unit)
|
| 0x00008000UL
|
STAT LID CHECKSUM FAIL
|
Checksm Verification for Legacy-ID feature failed
|
| 0x00000000UL
|
STAT_OK
|
OK
|
VISA ERROR CODES - Pipx40.h
You may receive an error code like -1074001918, this is a decimal number so needs to be converted to Hexidecimal before lookup below.| 0xbffc0800
|
pipx40_ERROR_BAD_SESSION
|
Not a valid pipx40 session
|
| 0xbffc0801
|
pipx40_ERROR_NO_INFO
|
Card information unobtainable - hardware problem
|
| 0xbffc0802
|
pipx40_ERROR_CARD_DISABLED
|
Card disabled - hardware problem |
| 0xbffc0803
|
pipx40_ERROR_BAD_SUB
|
Card has no sub-unit with specified number |
| 0xbffc0804
|
pipx40_ERROR_BAD_CHANNEL
|
Sub-unit has no channel with specified number |
| 0xbffc0805
|
pipx40_ERROR_NO_CAL_DATA
|
Sub-unit has no calibration data to read/write
|
| 0xbffc0806
|
pipx40_ERROR_BAD_ARRAY
|
Array type, hape or size is incorrect
|
| 0xbffc0807
|
pipx40_ERROR_MUX_ILLEGAL
|
Non-zero write data value is illegal for MUX sub-unit
|
| 0xbffc0808
|
pipx40_ERROR_EXCESS_CLOSURE
|
Sub-unit closure limit exceeded
|
| 0xbffc0809
|
pipx40_ERROR_ILLEGAL_MASK
|
One or more of the specified channels cannot be masked
|
| 0xbffc080A
|
pipx40_ERROR_OUTPUT_MASKED
|
Cannot activate an output that is masked
|
| 0xbffc080B
|
pipx40_ERROR_FAILED_INIT
|
Cannot open a Pickering card with this resource name
|
| 0xbffc080C
|
pipx40_ERROR_READ_FAIL
|
Failed read from hardware
|
| 0xbffc080D
|
pipx40_ERROR_WRITE_FAIL
|
Failed write to hardware
|
| 0xbffc080E
|
pipx40_ERROR_VISA_OP
|
VISA operation failure
|
| 0xbffc080F
|
pipx40_ERROR_VISA_VERSION
|
Incompatible VISA version
|
| 0xbffc0810
|
pipx40_ERROR_SUB_TYPE
|
Function incompatible with sub-unit type or capabilities
|
| 0xbffc0811
|
pipx40_ERROR_BAD_ROW
|
Matrix row value out-of-range
|
| 0xbffc0812
|
pipx40_ERROR_BAD_COLUMN
|
Matrix column value out-of-range
|
| 0xbffc0813
|
pipx40_ERROR_BAD_ATTEN
|
Attenuation value out-of-range
|
| 0xbffc0814
|
pipx40_ERROR_BAD_VOLTAGE
|
Voltage value out-of-range
|
| 0xbffc0815
|
pipx40_ERROR_BAD_CAL_INDEX
|
Calibration reference out-of-range
|
| 0xbffc0816
|
pipx40_ERROR_BAD_SEGMENT
|
Segment number out of range
|
| 0xbffc0817
|
pipx40_ERROR_BAD_FUNC_CODE
|
Function code value out of range
|
| 0xbffc0818
|
pipx40_ERROR_BAD_SUBSWITCH
|
Subswitch value out of range
|
| 0xbffc0819
|
pipx40_ERROR_BAD_ACTION
|
Action code out of range
|
| 0xbffc081A
|
pipx40_ERROR_STATE_CORRUPT
|
Cannot execute due to corrupt sub-unit state
|
| 0xbffc081B
|
pipx40_ERROR_BAD_ATTR_CODE
|
Unrecognised attribute code
|
| 0xbffc081C
|
pipx40_ERROR_EEPROM_WRITE_TMO
|
Timeout writing to EEPROM
|
| 0xbffc081D
|
pipx40_ERROR_ILLEGAL_OP
|
Operation is illegal in the sub-unit's current state
|
| 0xbffc081E
|
pipx40_ERROR_BAD_POT
|
Unrecognised pot number requested
|
| 0xbffc081F
|
pipx40_ERROR_MATRIXR_ILLEGAL
|
Invalid write pattern for MATRIXR/MATRIXS sub-unit
|
| 0xbffc0820
|
pipx40_ERROR_MISSING_CHANNEL
|
Attempted operation on non-existent channel
|
| 0xbffc0821
|
pipx40_ERROR_CARD_INACCESSIBLE
|
Card cannot be accessed failed/removed/unpowered
|
| 0xbffc0822
|
pipx40_ERROR_BAD_FP_FORMAT
|
Unsupported internal floating-point format (internal error)
|
| 0xbffc0823
|
pipx40_ERROR_UNCALIBRATED
|
Sub-unit is not calibrated
|
| 0xbffc0824
|
pipx40_ERROR_BAD_RESISTANCE
|
Unobtainable resistance value
|
| 0xbffc0825
|
pipx40_ERROR_BAD_STORE
|
Invalid calibration store number
|
| 0xbffc0826
|
pipx40_ERROR_BAD_MODE
|
Invalid mode value
|
| 0xbffc0827
|
pipx40_ERROR_SETTINGS_CONFLICT
|
Conflicting device settings
|
| 0xbffc0828
|
pipx40_ERROR_CARD_TYPE
|
Function call incompatible with card type or capabilities
|
| 0xbffc0829
|
pipx40_ERROR_BAD_POLE
|
Switch pole value out of range
|
| 0xbffc082A
|
pipx40_ERROR_MISSING_CAPABILITY
|
Attempted to activate a non-existent capability
|
| 0xbffc082B
|
pipx40_ERROR_MISSING_HARDWARE
|
Action requires hardware that is not present
|
| 0xbffc08C
|
pipx40_ERROR_HARDWARE_FAULT
|
Faulty hardware
|
| 0xbffc082D
|
pipx40_ERROR_EXECUTION_FAIL
|
Failed to execute (e.g. blocked by a hardware condition)
|
| 0xbffc082E
|
pipx40_ERROR_BAD_CURRENT
|
Current value out of range
|
| 0xbffc082F
|
pipx40_ERROR_BAD_RANGE
|
Invalid range value
|
| 0xbffc0830
|
pipx40_ERROR_ATTR_UNSUPPORTED
|
Attribute not supported
|
| 0xbffc0831
|
pipx40_ERROR_BAD_REGISTER
|
Register number out of range
|
| 0xbffc0832
|
pipx40_ERROR_MATRIXP_ILLEGAL
|
Invalid channel closure or write pattern for MATRIXP sub-unit
|
| 0xbffc0833
|
pipx40_ERROR_BUFFER_UNDERSIZE
|
Data buffer too small
|
| 0xbffc0834
|
pipx40_ERROR_ACCESS_MODE
|
Inconsistent shared access mode
|
| 0xbffc0835
|
pipx40_ERROR_POOR_RESISTANCE
|
Resistance outside limits
|
| 0xbffc0836
|
pipx40_ERROR_BAD_ATTR_VALUE
|
Bad attribute value
|
| 0xbffc0837
|
pipx40_ERROR_INVALID_POINTER
|
Invalid pointer
|
| 0xbffc0838
|
pipx40_ERROR_ATTR_READ_ONLY
|
Attribute is read only
|
| 0xbffc0839
|
pipx40_ERROR_ATTR_DISABLED
|
Attribute is disabled
|
| 0xbffc083A
|
pipx40_ERROR_PSU_MAIN_DISABLED
|
Main output is disabled, cannot enable the channel
|
| 0xbffc083B
|
pipx40_ERROR_OUT_OF_MEMORY_HEAP
|
Unable to allocate memory on Heap
|
| 0xbffc083C
|
pipx40_ERROR_INVALID_PROCESSID
|
Invalid ProcessID
|
| 0xbffc083D
|
pipx40_ERROR_SHARED_MEMORY
|
Shared memory error
|
| 0xbffc083E
|
pipx40_ERROR_CARD_OPENED_OTHER_PROCESS
|
Card is opened by a process in exclusive mode
|
| 0xbffc083F
|
pipx40_ERROR_DIO_PORT_DISABLED
|
DIO card PORT is disabled due to Over-Current Scenario
|
| 0xbffc0840 | pipx40_ERROR_DIO_INVALID_FILE | DIO pattern file is invalid |
| 0xbffc0841 | pipx40_ERROR_DIO_DYNAMIC_ACTIVE | DIO Dynamic operation is active, action not permissible |
| 0xbffc0842 | pipx40_ERROR_DIO_FILE_ENTRY_ERR | DIO File Entry has error, check the file entries |
| 0xbffc0844 | pipx40_ERROR_HW_INT_NOT_SUPPORTED | Hardware Interlock feature not supported for the card |
| 0xbffc0845 | pipx40_ERROR_HW_INT_ERROR | Hardware Interlock is not detected on the card, cannot use the function |
| 0xbffc0846 | pipx40_ERROR_SMS_CH_ENABLE_ERR | Channel is disabled, so Set-Measure-Set cannot be used |
| 0xbffc0847 | pipx40_ERROR_MEAS_CURRENT | Measured Current out of range |
| 0xbffc0848 | pipx40_ERROR_BAD_TEMPERATURE | Temperature value out of range |
| 0xbffc0849 | pipx40_ERROR_CMP_ENGINE_ON | Capture Engine running - operation unobtainable |
| 0xbffc084A | pipx40_ERROR_DDS_ON | DDS Engine running - operation unobtainable |
| 0xbffc084B | pipx40_ERROR_WAVEFORM_UNSUPPORTED | Waveform unsupported |
| 0xbffc084C | pipx40_ERROR_BAD_WAVEFORM | Operation unavailable for selected waveform |
| 0xbffc084D | pipx40_ERROR_FILE_UNAVAILABLE | File unavailable or does not exist |
| 0xbffc084E | pipx40_ERROR_FILE | File content invalid |
| 0xbffc084F | pipx40_ERROR_AMPLITUDE | Amplitude value out of range |
| 0xbffc0850 | pipx40_ERROR_WRITEPATTERN_ILLEGAL | Invalid write pattern |
| 0xbffc0851 | pipx40_ERROR_DC_OFFSET | DC Offset value out of range |
| 0xbffc0852 | pipx40_ERROR_FREQUENCY | Frequency value out of range |
| 0xbffc0853 | pipx40_ERROR_PHASE | Phase value out of range |
| 0xbffc0854 | pipx40_ERROR_DUTY_CYCLE | Duty Cycle value out of range |
| 0xbffc0855 | pipx40_ERROR_PULSE_WIDTH | Pulse Width value out of range |
| 0xbffc0856 | pipx40_ERROR_INVALID_COMP_FLAG | Invalid flag for setting compatibility logic |
| 0xbffc0fff | pipx40_ERROR_UNKNOWN | Unknown error code |
Card status bits for pipx40_getCardStatus and pipx40_getSubStatus results
Note: Two status codes may be combined together
0x10000000 + 0x02000000 = 0x12000000 (Disabled+HW_Fault) [eg Data loop 2 faulty]
| 0x80000000UL
|
pipx40_STAT_NO_CARD
|
No Pickering card open on the session
|
| 0x40000000UL
|
pipx40_STAT_WRONG_DRIVER
|
Card requires later driver version
|
| 0x20000000UL
|
pipx40_STAT_EEPROM_ERR
|
Error interpreting card EEPROM data
|
| 0x10000000UL
|
pipx40_STAT_DISABLED
|
Card is disabled
|
| 0x08000000UL
|
pipx40_STAT_NO_SUB
|
Card has no sub-unit with specified number
|
| 0x04000000UL
|
pipx40_STAT_BUSY
|
Busy (card or sub-unit)
|
| 0x02000000UL
|
pipx40_STAT_HW_FAULT
|
Hardware fault (eg. defective serial loop)
|
| 0x01000000UL
|
pipx40_STAT_PARITY_ERROR
|
PCIbus parity error
|
| 0x00800000U
|
pipx40_STAT_PSU_INHIBITED
|
PSU sub-unit - supply is disabled (by software)
|
| 0x00400000UL
|
pipx40_STAT_PSU_SHUTDOWN
|
PSU sub-unit - supply is shutdown (due to overload)
|
| 0x00200000UL
|
pipx40_STAT_PSU_CURRENT_LIMIT
|
PSU sub-unit - supply is operating in current-limited mode
|
| 0x00100000UL
|
pipx40_STAT_CORRUPTED
|
Sub-unit logical state is corrupted
|
| 0x00080000UL
|
pipx40_STAT_CARD_INACCESSIBLE
|
Card cannot be accessed (failed/removed/unpowered)
|
| 0x00040000UL
|
pipx40_STAT_UNCALIBRATED
|
Calibration data is faulty (card or sub-unit)
|
| 0x00020000UL
|
pipx40_STAT_CALIBRATION_DUE
|
Calibration is due (card or sub-unit)
|
| 0x00010000UL
|
pipx40_STAT_BIRST_ENABLED
|
BIRST is active (card or sub-unit
|
| 0x00008000UL
|
pipx40_STAT_LID_CHECKSUM_FAIL
|
Checksum Verification for Legacy-ID feature failed
|
| 0x00000000UL
|
pipx40_STAT_OK
|
|
ClientBridge Driver Error Codes
PIPLX
| 0
|
NO_ERR
|
No error
|
| 1
|
ER_NO_CARD
|
No Pickering card has the specified number
|
| 2
|
ER_NO_INFO
|
Card information unobtainable - hardware problem
|
| 3
|
ER_CARD_DISABLED
|
Specified card is disabled
|
| 4
|
ER_BAD_SUB
|
Sub-unit value out of range for target card
|
| 5
|
ER_BAD_BIT
|
Bit number out of range for target sub-unit
|
| 6
|
ER_NO_CAL_DATA
|
Target sub-unit has no calibration data to read/write
|
| 7
|
ER_BAD_ARRAY
|
"SafeArray type, shape or size in incorrect"
|
| 8
|
ER_MUX_ILLEGAL
|
Non zero write data value is illegal for MUX sub-unit
|
| 9
|
ER_EXCESS_CLOSURE
|
Execution would cause closure limit to be exceeded
|
| 10
|
ER_ILLEGAL_MASK
|
One or more of the specified channels can not be masked
|
| 11
|
ER_OUTPUT_MASKED
|
Can not activate an output that is masked
|
| 12
|
ER_BAD_LOCATION
|
Can not open a Pickering card at the specified location
|
| 13
|
ER_READ_FAIL
|
Failed read from hardware
|
| 14
|
ER_WRITE_FAIL
|
Failed write to hardware
|
| 15
|
ER_DRIVER_OP
|
Hardware driver failure
|
| 16
|
ER_DRIVER_VERSION
|
Incompatible hardware driver version
|
| 17
|
ER_SUB_TYPE
|
Function call incompatible with sub-unit type or capabilities
|
| 18
|
ER_BAD_ROW
|
Matrix row value out of range
|
| 19
|
ER_BAD_COLUMN
|
Matrix column value out of range
|
| 20
|
ER_BAD_ATTEN
|
Attenuation value out of range
|
| 21
|
ER_BAD_VOLTAGE
|
Voltage value out of range
|
| 22
|
ER_BAD_CAL_INDEX
|
Calibration index value out of range
|
| 23
|
ER_BAD_SEGMENT
|
Segment number out of range
|
| 24
|
ER_BAD_FUNC_CODE
|
Function code value out of range
|
| 25
|
ER_BAD_SUBSWITCH
|
Subswitch value out of range
|
| 26
|
ER_BAD_ACTION
|
Action code out of range
|
| 27
|
ER_STATE_CORRUPT
|
Cannot execute due to corrupt sub-unit state
|
| 28
|
ER_BAD_ATTR_CODE
|
Unrecognized attribute code
|
| 29
|
ER_EEPROM_WRITE_TMO
|
Timeout writing to EEPROM
|
| 30
|
ER_ILLEGAL_OP
|
Operation is illegal in the sub-unit's current state
|
| 31
|
ER_BAD_POT
|
Unrecognized pot number requested
|
| 32
|
ER_MATRIXR_ILLEGAL
|
Invalid write pattern for MATRIX/MATS sub-unit
|
| 33
|
ER_MISSING_CHANNEL
|
Attempted operation on non-existent channel
|
| 34
|
ER_CARD_INACCESSIBLE
|
Card can not be accessed (failed/removed/unpowered)
|
| 35
|
ER_BAD_FP_FORMAT
|
Unsupported internal floating-point format (internal error)
|
| 36
|
ER_UNCALIBRATED
|
Sub-unit is not calibrated
|
| 37
|
ER_BAD_RESISTANCE
|
Unobtainable resistance value
|
| 38
|
ER_BAD_STORE
|
Invalid calibration store number
|
| 39
|
ER_BAD_MODE
|
Invalid mode value
|
| 40
|
ER_SETTINGS_CONFLICT
|
Conflicting device settings
|
| 41
|
ER_CARD_TYPE
|
Function call incompatible with card type or capabilities
|
| 42
|
ER_BAD_POLE
|
Switch pole value out of range
|
| 43
|
ER_MISSING_CAPABILITY
|
Attempt to activate a non-existent capability
|
| 44
|
ER_MISSING_HARDWARE
|
Action requires hardware that is not present
|
| 45
|
ER_HARDWARE_FAULT
|
Faulty hardware
|
| 46
|
ER_EXECUTION_FAIL
|
Failed to execute (e.g. blocked by a hardware condition)
|
| 47
|
ER_BAD_CURRENT
|
Current value out of range
|
| 48
|
ER_BAD_RANGE
|
Invalid range value
|
| 49
|
ER_ATTR_UNSUPPORTED
|
Attribute not supported
|
| 50
|
ER_BAD_REGISTER
|
Register number out of range
|
| 51
|
ER_MATRIXP_ILLEGAL
|
Invalid channel closure or write pattern for MATRIXP sub-unit
|
| 52
|
ER_BUFFER_UNDERSIZE
|
Data buffer too small
|
| 53
|
ER_ACCESS_MODE
|
Inconsistent shared access mode
|
| 54
|
ER_POOR_RESISTANCE
|
Unobtainable resistance value
|
| 55
|
ER_BAD_ATTR_VALUE
|
Unrecognised attribute value
|
| 56
|
ER_INVALID_POINTER
|
Invalid Pointer
|
| 57
|
ER_ATTR_READ_ONLY
|
Attribute is read-only
|
| 58
|
ER_ATTR_DISABLED
|
Attribute is disabled
|
| 59
|
ER_PSU_MAIN_OUTPUT_DISABLED
|
Main output is disabled, cannot enable the channel
|
| 60 | ER_OUT_OF_MEMORY_HEAP | Unable to allocate memory on Heap |
| 61 | ER_INVALID_PROCESSID | Invalid ProcessID |
| 62 | ER_SHARED_MEMORY | Shared memory error |
| 63 | ER_CARD_OPENED_OTHER_PROCESS | Card is opened by a process in exclusive mode |
| 64 | ER_DIO_PORT_DISABLED | DIO card PORT is disabled due to Over-Current Scenario |
| 65 | ER_DIO_INVALID_FILE | DIO pattern File is invalid |
| 66 | ER_DIO_DYNAMIC_ACTIVE | DIO dynamic operation active, action not permissible |
| 67 | ER_DIO_FILE_ENTRY_ERR | DIO file entry error, check file entries |
| 69 | ER_HW_INT_NOT_SUPPORTED | Hardware Interlock feature not supported for the card |
| 70 | ER_HW_INT_ERROR | Hardware Interlock is not detected on the card, cannot use the function |
| 71 | ER_SMS_CH_ENABLE_ERR | Channel is disabled, so Set/Measure/Set cannot be used |
| 72 | ER_MEAS_CURRENT | Measured current out of range |
| 73 | ER_BAD_TEMPERATURE | Temperature value out of range |
| 74 | ER_CMP_ENGINE_ON | Capture engine running - operation unobtainable |
| 75 | ER_WRITEPATTERN_ILLEGAL | Invalid write pattern |
| 87 | ER_INVALID_COMP_FLAG | Invalid flag for setting compatibility logic |
| 8194
|
ER_PIPLX_FUNC_NOT_LOADED
|
Function not loaded from library |
| 8195
|
ER_PIPLX_NOT_CONNECTED
|
You are not connected to remote host
|
| 8196
|
ER_PIPLX_FUNC_NOT_LOCAL
|
Function not supported on localhost
|
| 8199
|
ER_PIPLX_RESMAN_NOT_AVAILABLE
|
Pickering Resource Manager is not available
|
| 8200
|
ER_PIPLX_INVALID_RSRC
|
Invalid resource string
|
|
|
|
|
PICMLX |
|
|
| 4098
|
ER_PICMLX_CLI_INVALID_SESSION
|
Client: Invalid session ID
|
| 4099
|
ER_PICMLX_CLI_HOST_UNAVAILABLE
|
Client: Destination host is unavailable
|
| 4109
|
ER_PICMLX_CLI_CONNECT
|
Client: Can't connect to device
|
| 4110
|
ER_PICMLX_CLI_CONNECT REFUSED
|
Client: Connection refused
|
| 4111
|
ER_PICMLX_CLI_NAME NOT KNOWN
|
Client: Name not known
|
| 4112
|
ER_PICMLX_CLI_RECV_FAILED
|
Client: Can't receive data
|
| 4113
|
ER_PICMLX_CLI_RECV_DATA
|
Client: Received corrputed data
|
| 4114
|
ER_PICMLX_CLI_SEND_FAILED
|
Client: Can't send data
|
| 4115
|
ER_PICMLX_CLI_FUNC_NOT_LOCAL
|
Client: Function is not supported on local system
|
| 4116
|
ER_PICMLX_CLI_NOT_CONNECTED
|
Client: Session isn't connected to the device
|
| 4117
|
ER_PICMLX_SRV_RPC_DATA
|
Server: RPC data corrupt
|
| 4118
|
ER PICMLX CLI DATA NOT ACCEPT | Client: Invalid parameter value
|
| 4119
|
ER_PICMLX_SRV_INVALID_FID
|
Server: Invalid function ID
|
| 4120
|
ER_PICMLX_SRV_RPC_DATA
|
Server: RPC data are corrupted
|
| 4121
|
ER_PICMLX_SRV_INVALID_CARDID
|
Server: Invalid card ID
|
| 4122
|
ER_PICMLX_SRV_INVALID_ADDRESS
|
Server: Address of card is invalid
|
| 4123
|
ER_PICMLX_SRV_OPEN_CARD
|
Server: The card is used
|
| 4124
|
ER_PICMLX_SRV_ACCESS_DENIED
|
Server: You haven't any rights to the card(s)
|
| 4125
|
ER_PICMLX_SRV_NOT_SUPPORTED
|
Server: Function is not supported by this LXI device
|
| 4126
|
ER_PICMLX_SRV_DEVICE_INFO
|
Server: Information about LXI device is not obtainable
|
| 4127
|
ER_PICMLX_SRV_OUT_OF_RESOURCES
|
Server: Out of resources (probably memory)
|
| 4128
|
ER_PICMLX_SRV_DATA_LENGTH
|
Server: Required length of data is too long
|
| 4129
|
ER_PICMLX_SRV_CARD_TYPE
|
Server: LXI device has no card of this type
|
| 4130
|
ER_PICMLX_SRV_FUNC_NOT_IMPL
|
Server: Function is not implemented or it is reserved
|
| 4131
|
ER_PICMLX_SRV_CARD_USED_BYCLI
|
Server: The card is already used by the client
|
| 4132
|
ER_PICMLX_SRV_UNDEFINED
|
Server: Undefined error
|
| 4133
|
ER_PICMLX_SRV_WAIT_TIMEOUT
|
Server: Wait timeout expired
|
| 4134
|
ER_PICMLX_SRV_DEVICE_LOCKED
|
Server: Device is locked - another client has exclusive access
|
| 4135
|
ER_PICMLX_CLI_BEGINTRANS
|
Client: Transmission wasn't initiated. First call PICMLX_BeginTransmission!
|
| 4136
|
ER_PICMLX_CLI_ENDTRANS
|
Client: Previous transmission wasn't ended. Call PICMLX_EndTransmission !
|
| 4137
|
ER_PICMLX_CLI_INVALID_INDEX
|
Client: Invalid list item index
|
| 4138
|
ER_PICMLX_CLI_DIRECTECHO_FAILED
|
Client: Direct discovery function failed
|
| 4139
|
ER_PICMLX_CLI_BROADCASTECHO_FAILED
|
Client: Broadcast discovery function failed
|
| 4140
|
ER_PICMLX_SRV_INVALID_SESSION
|
Server: Invalid session
|
| 4141
|
ER_PICMLX_SRV_INVALID_TOKEN
|
Server: Invalid token
|
| 4142
|
ER_PICMLX_SRV_INVALID_EC
|
Server: Invalid error code
|
| 4143
|
ER_PICMLX_SRV_FATAL_01
|
Server: Fatal error – 1
|
| 4144
|
ER_PICMLX_CLI_TIMEOUT_FAIL
|
Client: Can not set recv/send socket timeout
|
| 4145
|
ER_PICMLX_CLI_RECV_TIMEDOUT
|
Client: Can't receive data. Connection timed out
|
| 4146
|
ER_PICMLX_CLI_RECV_RSRC_TEMP_UNAVAILABLE
|
Client: Can't receive data. Resource temporarily unavailable
|
| 4147
|
ER_PICMLX_SRV_DATACOPY
|
Server: Error while copying output data to response buffer
|
| 4148
|
ER_PICMLX_SRV_CREATE_DIRECTORY_FAILED
|
Server: Create directory failed
|
| 4149
|
ER_PICMLX_SRV_DELETE_DIRECTORY_FAILED
|
Server: Delete directory failed
|
| 4150
|
ER_PICMLX_SRV_DELETE_FILE_FAILED
|
Server: Delete file failed
|
| 4151
|
ER_PICMLX_SRV_DIRECTORY_NOT_EXISTS
|
Server: Directory doesn't exist
|
| 4152
|
ER_PICMLX_SRV_FILE_NOT_EXISTS
|
Server: File doesn't exist
|
| 4153
|
ER_PICMLX_SRV_FILE_OPEN_FAILED
|
Server: File open failed
|
| 4154
|
ER_PICMLX_SRV_FILE_READ_FAILED
|
Server: File read failed
|
| 4155
|
ER_PICMLX_SRV_NO_FILE_TRANSFER
|
Server: No file transfer
|
| 4156
|
ER_PICMLX_SRV_FILE_WRITE_FAILED
|
Server: File write failed
|
| 4157
|
ER_PICMLX_SRV_SET_ATTRIBUTES_FAILED
|
Server: Set directory/file attributes failed
|
| 4158
|
ER_PICMLX_CLI_FILE_OPEN_FAILED
|
Client: Open file failed
|
| 4160 | ER_PICMLX_CLI_OUT_OF_RESOURCES | Client: Out of resources (probably memory) |
| 4161 | ER_PICMLX_VXI_NOACCESS | VXI-11: Device not accessible |
| 4162 | ER_PICMLX_VXI_PARAMERR | VXI-11: Parameter error |
| 4163 | ER_PICMLX_SRV_PROTECTIONRESET_PERFORMED | Protection Reset was performed |
|
|
|
|
PIFGLX |
||
| 4353 | ER_PIFGLX_NULLPOINTER | nullpointer exception |
| 4354 | ER_PIFGLX_FUNC_NOT_LOADED | function not loaded |
| 4428 | ER_PIFGLX_DDS_ON | DDS Engine running - operation unobtainable |
| 4429 | ER_PIFGLX_WAVEFORM_UNSUPPORTED | Waveform unsupported |
| 4430 | ER_PIFGLX_BAD_WAVEFORM | Operation unavailable for selected waveform |
| 4431 | ER_PIFGLX_FILE_UNAVAILABLE | File unavailable or does not exist |
| 4432 | ER_PIFGLX_BAD_FILE | File content invalid |
| 4433 | ER_PIFGLX_BAD_AMPLITUDE | Amplitude value out of range |
| 4434 | ER_PIFGLX_BAD_DC_OFFSET | DC Offset value out of range |
| 4435 | ER_PIFGLX_BAD_FREQUENCY | Frequency value out of range |
| 4436 | ER_PIFGLX_BAD_PHASE | Phase value out of range |
| 4437 | ER_PIFGLX_BAD_DUTY_CYCLE | Duty Cycle value out of range |
| 4438 | ER_PIFGLX_BAD_PULSE_WIDTH | Pulse Width value out of range |
|
|
|
|
PIPSLX |
|
|
| 12289
|
ER_PIPSLX_INVALID_SESSION
|
No longer used - now ER_PICMLX_INVALID_SESSION
|
| 12290
|
ER_PIPSLX_FUNC_NOT_LOCAL
|
Function not supported on local host
|
| 12291
|
ER_PIPSLX_NOT_CONNECTED
|
Not connected to remote host
|
| 12292
|
ER_PIPSLX_NOT_INIT
|
Library not initialized
|
| 12293
|
ER_PIPSLX_SWITCH_FAULT
|
Switch fault
|
| 12294
|
ER_PIPSLX_BAD_FORMAT_DATA
|
Data or command format bad
|
| 12295
|
ER_PIPSLX_UNKNOWN_CMD
|
Unknown command
|
| 12296
|
ER_PIPSLX_BUSY
|
Device busy
|
| 12297
|
ER_PIPSLX_SEQUPINPROGRESS
|
Up sequence in progress
|
| 12298
|
ER_PIPSLX_SEQDOWNINPROGRESS
|
Down sequence in progress
|
| 12299
|
ER_PIPSLX_CHANTESTINPROGRESS
|
Channel test running
|
| 12300
|
ER_PIPSLX_EMERGENCYSTOP
|
Emergency stop button engaged
|
| 12301
|
ER_PIPSLX_PARAM_SIZE
|
Parameter is NULL or invalid size |