Accommodating 131 signals and with more than 2km of wire, the complex wiring harness was needed to improve the accuracy of a hardware-in-the-loop test system and to accommodate new tests.

Cables

Modern jet engine aircraft have at least one fuel control system, responsible for precisely metering and delivering the correct amount of fuel to the engine’s combustion chambers in response to pilot commands and changing flight conditions.

The system automatically regulates engine thrust, ensuring optimal performance, efficiency, and safety at all times. It also prevents dangerous conditions such as compressor stalls, flameouts and temperatures exceeding safe limits.

Not surprisingly, a fuel control system is safety-critical and must be regularly tested to ensure there is no degradation in its performance over time. Test is not simple, though, and requires providing the system with a variety of inputs and monitoring its many outputs.

Test

One company that regularly performs fuel control system tests is a major European-based airline that also provides MRO services. They have a hardware-in-the-loop (HIL) test system/station. It is computer-controlled and includes fuel injectors, actuators, and sensors (i.e., everything with which the fuel control system connects when on an aircraft), plus a variety of test and measurement (T&M) equipment. The HIL system also has a complex, four-part wiring harness needed to make all the necessary connections.

In late 2024, the airline decided it needed to improve the accuracy of the measurements being taken and recorded, and that a greatly improved wiring harness would be required. Specifically, the original harness had some grounding and shielding issues. These resulted in a 5% error (due to signal crosstalk) when reading the position of control solenoids. A major objective of the harness redesign was to eliminate crosstalk and, by extension, the associated errors.

Other objectives included improving measurement accuracy by switching to the ‘4-wire’ measurement technique for certain tests, accommodating an increase in voltage (from 50 to 500V) used for insulation resistance tests, and enabling the overall test system to self-calibrate.

The airline turned to us for a high-quality replacement, as we specialize in custom cable assembly and connectivity solutions.

Design

During Q4 2024 and Q1 2025, our cable specialists worked closely with the airline’s engineer (responsible for the HIL test system), who modified the original schematic to reflect several new connections. For this, they used our Cable Design Tool (CDT), which helps reduce resources and facilitate collaboration in creating custom cables.

It is a web-based tool that allows users to graphically design a custom cable assembly by using either the tool’s built-in library of standard cable sets or creating one from scratch. The tool is intuitive, and the airline’s engineers were able to design most of the harness themselves despite the complexity of the design and having little to no previous experience with CDT.

During the design phase, our cable specialists—extremely familiar with what is needed to progress from a schematic to a right-first-time, physical build—advised the airline’s engineers on several key decisions. These included: selecting wire gauges based on current-carrying requirements, recommending suitable backshells for a test card in the HIL system, adjusting path lengths to maintain correct bend radii, idents, specifically, printing signal names on the cables to improve clarity, the identification of alternative parts (to reduce lead times as much as possible), and refining how to implement loopbacks. Figure 1 shows a rendering of the airline’s engineer’s design.

Cables on monitor

Figure 1 – Above, a rendering of the harness in CDT. The stats: 131 signals accommodated, 28 D-Type connectors (a mix of 37- and 50-pin), four 160-pin connectors (DIN41612), two 500-pin SEARAY connectors and four banana jacks

A senior engineer at the airline commented,

Thanks to the close collaboration between Pickering's cable experts, our engineers, and the use of Pickering’s Cable Design Tool as a shared resource and means of exchanging information, we soon had our design.

Manufacture & Test

In mid-March, the airline’s designers signed off on their design, and the order was placed for assembly to commence (see figure 2). It is worth noting, though, that just before work began, one of our specialists caught a design error [or rather some incorrectly specified parts] that, had the error not been found, would have taken a long time (plus cost) to fix if the order had proceeded unchecked.

A key tool in harness manufacture was our Cable Build Assistant. It automatically pulled all signal routing data directly from the design created in CDT, and showed our assemblers exactly which wires to connect to which pins and which wire types/gauges to use.

The senior designer added, 

The beauty of the Cable Build Assistant is that we didn’t have to explain to Pickering how our schematic should be interpreted. All the details regarding wire types and gauges were within the design tool.


Cable Construction

Figure 2 – Assembly followed the approved design, with every wire tagged with its corresponding identification number (as shown in the schematic).

Regarding the cables, most paths are double-screened, i.e., there are two layers of shielding. Typically, this involves a foil screening the individual wires, plus a braided screen around the wire pairs for 2-core cables and groups of three for 3-core cables. This approach provides enhanced protection against EMI and was selected by the airline’s engineers due to the high sensitivity of the signals being carried.

Four different wire gauges were used: 20 AWG for circuits with up to 2A current, 22 AWG for 1A and 24 AWG for 0.5A. All other connections, i.e., those without a specific current-carrying requirement, used either 24 or 26 AWG. In total, over 2km of wire was used.

Post-manufacture, the harness was subjected to our rigorous test procedures. The sequence was as follows:

Low voltage (4V, 1mA to 1A) tests: 
  •  Continuity checks for shorts, missing contacts, and any mis-wires. 
  •  4-wire path resistance checks (0.001 to 10Ω ±2% ±001Ω). 
 High voltage (100V to 2kVDC) tests:
  •  Insulation resistance (5MΩ to 1GΩ ±10%). 
  •  Dielectric withstand test.

The Outcome

The new harness was delivered in early July, and the airline’s engineers saw immediate improvements in the performance of their HIL test system. As hoped, test accuracy was significantly improved thanks to better shielding and by switching to 4-wire measurements in some cases.

The entire project was completed relatively quickly for such a complex harness, and any short delays experienced were due to long lead times on certain wire types. Although outside the control of the airline and Pickering, as mentioned, alternatives had been selected early on to reduce lead times as much as possible.

The use of the Cable Design Tool and Cable Build Assistant, along with close collaboration between the airline’s engineers and our cable specialists, greatly contributed to the project’s success.

The people, the skill sets, and the tools, everything really gelled,” concluded the senior designer. “This led to us receiving a high-quality, 131-signal, four-part wiring harness that worked as soon as we connected it between a fuel control system and our HIL test system.

Impressed by the speed with which the new harness was designed and manufactured, the airline has since expressed interest in upgrading the wiring harnesses of two other HIL test systems.

Don’t Be Left Behind on Your HIL Testing Strategies 

Learn more on how we can help you keep on pace.

Learn More

Beta

How can I help?

Hi , I'm TESS - your friendly AI agent

Press Enter to submit

TESS is a moderated, AI agent. TESS can make mistakes, please verify important information independently.


Chat history

Log in or create an account to save & continue your chats with TESS.

Log in

or create an account