PXI Chassis & PXIe Chassis
A PXI or PXIe chassis is the backbone of a modular test system. It houses PXI or PXIe peripheral modules, supplies DC power, provides forced-air cooling, and carries the PCI or PCI Express bus, along with PXI-specific timing and synchronization signals that enable a controller to communicate with every installed module.
What Do PXI & PXIe Chassis Do?
A PXI(e) chassis performs four core functions for a test system: it houses and powers the installed peripheral modules, cools them with forced air, carries the PCI or PCIe backplane bus between the controller and each module, and distributes the timing, triggering, and synchronization signals that coordinate module operation.
The PXI architecture enables engineers to build test systems that combine multiple instrumentation, switching, control, or communication functions, such as digitizers, source/measure units, or switching matrices, in a compact, flexible, and tightly integrated industry-standard modular format. Because the system’s chassis is fully PXI-compliant, it accepts modules from any PXI Systems Alliance member, which gives you the flexibility to mix and match vendors within a single system.
Pickering offers a range of PXI and PXI Express (PXIe) chassis in 8- to 21-slot configurations. Our Gen 2 and Gen 3 PXIe chassis provide full hybrid capability across every peripheral slot, so you can combine PXI and PXIe modules with the embedded or remote controller that best fits your test requirements. Our PXI chassis enable legacy test systems to continue to be supported in critical long-life applications.
PXI vs. PXIe Chassis: Which Do You Need?
Use the table below to narrow your choice before comparing individual models.
| Consideration | PXI Chassis | PXIe Hybrid Chassis |
|---|---|---|
| Backplane bus | Parallel PCI (32-bit, 33 MHz) | Serial PCIe (Gen 2 or Gen 3) |
| Maximum bandwidth | Up to 132 MB/s | Up to several GB/s, depending on Gen and lane count |
| Module compatibility | PXI-1 and PXI-H modules | PXI-H or PXIe modules in the same hybrid slot |
| Best suited for | Switching and lower data-rate instrumentation | High-speed data acquisition, RF, and mixed PXI/PXIe systems |
| Slot counts available | 8, 14, and 19 | 8, 18, and 21 |
If your modules are a mix of PXI and PXIe, a full hybrid chassis gives you the most flexibility, since every peripheral slot accepts either type.
PXI and PXIe Chassis Families
| Product / Family | Purpose | Application | Technical Range |
|---|---|---|---|
| PXIe Full Hybrid Chassis, Gen 2 | Provides hybrid peripheral slots that accept both PXI-H and PXIe modules. | Suited to mixed-vendor systems combining legacy PXI modules with newer PXIe instrumentation. | 18- (with timing slot) and 21-slot versions; PCIe Gen 2 backplane; front or rear rack-mount options. |
| PXIe Full Hybrid Chassis, Gen 3 | Deliver the highest backplane bandwidth in Pickering's PXIe range across hybrid peripheral slots. | Suited to data-intensive applications such as high-speed digitizers and RF instrumentation. | 8- and 18-slot (with timing slot) configurations; PCIe Gen 3 backplane; front, rear, or non-rack-mount options. |
| PXI Chassis (8 to 19 Slots) | Houses 3U PXI or cPCI modules on a fully compliant PXI backplane. | Best suited for switching, basic digital and analog I/O, and applications that do not require PXIe data bandwidth. | 8-, 14-, and 19-slot versions; 32-bit PCI bus at 33 MHz; up to 132 MB/s backplane throughput. |
| Chassis Mounting Kits | Adds rack-mounting hardware to compatible chassis. | Required when installing a chassis into a standard 19-inch rack. | Kits are matched to specific chassis models; confirm compatibility before ordering. |
Software, Compatibility, and Connectivity
Every Pickering PXI(e) chassis supports standard VISA and IVI driver architectures, so your modules integrate with Windows and Linux test environments without custom low-level programming. Because all chassis are built to the PXI Systems Alliance specification, they work with embedded controllers (PXIe chassis) and remote PCIe controllers (PXIe and PXI chassis), giving you flexibility in controlling your test system. For applications that call for Ethernet rather than PCI(e) control, our LXI/USB chassis accept all of our 3U PXI switching, simulation and instrumentation modules. If your system needs cabling between the chassis and your device under test, our range of in-house manufactured cables and connectors, including custom assemblies, supports fast and effective integration.
Frequently Asked Questions
Can I mix PXI and PXIe modules in the same chassis?
What's the difference between a Gen 2 and Gen 3 PXIe chassis?
Does a Pickering PXI or PXIe chassis only accept Pickering modules?
How do I know how many slots I need?
Design Your Chassis Configuration
Not sure which slot count, bus generation, or controller combination fits your application? Use our Test System Architect tool to configure your chassis, modules, and signal paths in a single workflow, or consult our Product Selector to compare chassis specifications directly. For custom rack or power requirements, contact our applications engineering team directly.