PXI Thermocouple Simulators
PXI thermocouple simulators are modular signal sources that generate precise, low-level millivolt outputs to replicate the signals produced by real thermocouples. Test engineers use them to emulate temperature sensors during hardware validation, most commonly in Electronic Control Unit (ECU) testing, without the need for physical heat sources or reference ovens..
Pickering's PXI millivolt thermocouple simulator modules provide 32, 24, 16, or 8 channels of accurate low-voltage sources. Each channel operates across one of three voltage ranges, covering most thermocouple types, including noble and rare metals. This makes them well-suited to sensor emulation in Hardware-in-the-Loop (HIL) applications, where accurate, repeatable stimuli are critical for verifying control system behavior. We also supply connection solutions, including compensation blocks, so you can integrate the simulator into your existing test system with minimal effort.
How Do PXI Thermocouple Simulators Work?
A thermocouple produces a small voltage (typically in the millivolt range) that varies with temperature. A thermocouple simulator reverses this relationship: it outputs a precise millivolt signal that corresponds to a specific simulated temperature.
By connecting a simulator in place of a physical sensor, you can drive an ECU or measurement system through a full range of temperature conditions in software. This removes the cost, delay, and repeatability issues associated with heating and cooling real sensors and lets you exercise fault conditions and edge cases that would be difficult to reproduce with physical hardware.
Pickering's thermocouple simulators install in any compliant PXI chassis or a Hybrid slot in a PXIe chassis and can also be hosted in Pickering's LXI/USB modular chassis for remote control over Ethernet or USB.
Choosing the Right Thermocouple Simulator
Pickering offers two families of thermocouple simulator modules. The right choice depends on whether your channels require isolation and how you plan to configure your voltage ranges.
41–760 Millivolt Thermocouple Simulator
The 41–760 series provides multiple low-voltage sources in a non-isolated design. It's a cost-effective option for applications that don't require channel-to-channel isolation.
- Purpose: General-purpose thermocouple and low-millivolt sensor simulation
- Application: ECU testing and sensor emulation where isolation isn't required
- Channels: 8, 16, 24, or 32
- Configuration: Selectable voltage ranges covering most thermocouple types
41-761A Analog Output/Thermocouple Simulator
The 41-761A series provides isolated low-voltage outputs configured to a fixed voltage range for each model, delivering consistent performance for both thermocouple simulation and general analog output tasks.
- Purpose: Isolated thermocouple simulation and precise analog output
- Application: ECU and sensor emulation requiring a specific, defined output ranged
- Channels: 8, 16, or 24
- Configuration: Fixed range per model: ±100mV, ±250mV, ±500mV, ±1000mV, ±1500mV, or ±2000mV
Which Module Should You Choose?
Use the criteria below to match a module family to your application:
| Requirement | Recommended Family |
|---|---|
| Lowest cost, no isolation needed | 41-760 (Millivolt Simulator) |
| Channel-to-channel isolation | 41-761 (Isolated Millivolt Simulator) |
| Isolation with a fixed, defined output range | 41-761A (Analog Output/Thermocouple Simulator) |
| Highest channel density (32 channels) | 41-760 |
| Selectable voltage ranges across most thermocouple types | 41-760 or 41-761 |
If you're unsure which range best fits your thermocouple types, contact your local Pickering engineer.
Connectivity and Integration
To simplify integration into your test system, Pickering supplies the 40–965–912 Compensation Block for the 41–760 and 41–761 thermocouple simulators. Compensation blocks provide cold-junction compensation, which is essential for accurate thermocouple simulation when interfacing with real measurement hardware.
All Pickering PXI fault insertion modules plug into any compliant PXI chassis or a Hybrid slot in a PXIe chassis and can also be hosted in Pickering's LXI/USB modular chassis for remote control over Ethernet or USB. This flexibility lets you deploy the same module across bench, rack, and distributed test systems without changing your core hardware.
We also supply mating cables and connectors to complete your signal path. For guidance on connectivity, visit our cables and connectors page.
Software and Driver Support
Pickering thermocouple simulators are supported by our comprehensive range of Windows and Linux drivers, available for free download. Our simulation software, included with the PXI driver installation, lets you develop and verify test system software independently of the physical hardware. This means your test program development can begin before modules arrive, reducing overall project lead time.